Sunday, 22 July 2012
Saturday, 21 July 2012
If you have an psp vita that has wifi and 3g compatibility, then you can access the internet content on the gaming system using a 3g sim card, which has a data plan or tariff added onto it. Depending on the network you are using, the cost of plans are fairly cheap, but prices do tend to increase if you are wanting lots of internet usage data. This makes it convenient for your psp vita to access internet content, when a wifi access point is not available for you to use with the console. The 3g version of the psp vita console acts just like a smartphone, when you insert a sim card into the device, the psp will connect to a phone transmitter and access the internet the way a mobile phone access it.
Instructions are straight forward:
1) Power off your psp vita console, place the console down and then remove the sim card from its packaging.
2) Once you have removed the sim from its packaging, read through the leaflets provided with it, this is so you can read the internet plan offers, to see which one suits your need the best. Pick a large data bundle if you are going to use internet access on the psp vita for numerous hours on a daily basis or chose a plan with less data, if you are not going to use internet on your psp vita often.
3) Once you have decided which plan is the best for you, go ahead and top the sim card up and select the tariff you want to add onto the sim card. Once you have done that, you are then ready to insert into the sim card slot found on the console itself.
4) The sim card slot is located on the left hand side of the console, like shown in the image below.
6) Remove the sim card holder from the psp vita, then insert your sim card into the holder the correct way, like shown in the above picture.
7) Then insert the sim card holder back into the slot on the psp console and power on your psp vita.
Thursday, 19 July 2012
If a electrical item you have doesn't work, its very likely that the fuse inside the appliance that protects the circuit, is blown out. If you don't have the proper testing equipment, like a multimeter or a test screwdriver, to test the fuse if its working or not, then as a alternative method, you can create your own homemade device to check fuses. The device that you can make is basically an simply bulb circuit, instead of placing an inline switch in the circuit, you will have two wires that you attach to each end of the fuse. If the bulb lights up, then the wire inside the fuse is good and is not burnt out and if the bulb doesn't light up, then the fuse is blown and you will need to obtain an replacement fuse.
Instructions are very simple:
1) You will need to obtain a bulb holder with a working bulb, you can get these from small electrical hardware shops. Screw the bulb into the bulb holder and using a Philips screwdriver, unscrew the two screws on each side of the bulb holder, this is so you can insert a wire into each screw.
2) Insert the braid of the wire into one screw, found on one side of the bulb and using the screwdriver, screw the screw tight. Then insert the other wire's braid into the other screw, found on the opposite side and again using your screwdriver screw it tight.
3)Once them wires have been connected to the bulb holder, you will need to a power source to power the circuit, this can be an battery and a battery holder, to hold it in place. Insert the battery into the battery holder and locate the two terminals found on the back of it. One will be an positive + and the other will be negative -.
Instructions are very simple:
1) You will need to obtain a bulb holder with a working bulb, you can get these from small electrical hardware shops. Screw the bulb into the bulb holder and using a Philips screwdriver, unscrew the two screws on each side of the bulb holder, this is so you can insert a wire into each screw.
2) Insert the braid of the wire into one screw, found on one side of the bulb and using the screwdriver, screw the screw tight. Then insert the other wire's braid into the other screw, found on the opposite side and again using your screwdriver screw it tight.
3)Once them wires have been connected to the bulb holder, you will need to a power source to power the circuit, this can be an battery and a battery holder, to hold it in place. Insert the battery into the battery holder and locate the two terminals found on the back of it. One will be an positive + and the other will be negative -.
Saturday, 14 July 2012
If you are using your iphone 4 on an daily basis to make calls to friends, family and work collegues, you will properly likely to experience call dropping and getting disconnected every so often when using the device to make a call. Your properly puzzled why the calls keep getting dropped and so was i. This was a very annoying problem because callers on the other end will eventually get annoyed at your phone calls, as they keep dropping. There are a couple of reasons, as well as solutions to solve the problem, based on why the signal problem happens and i would like to share them with you, to prevent this problem reoccurring again and again.
1) You are likely to have an weak signal from your network provider, from there phone mast. If a network provider provided in your area, where you are using the iphone4 to make calls and browse the internet is poor, it will not function properly and the calls will get dropped, when there is no signal and the internet connection will become really slow and unusable. The way to get around this is to check your networks coverage in your area, this is to see if its strong or weak. If its weak, then try moving onto a 2g signal or change the network provider, as that is the cause to this sort of problem. If its strong, then consider solutions 2, 3 & 4.
2) The network provider of the sim card inside your iphone 4 could be carrying out some mechanical work to the phone mast, as it might need some maintenance. If this happens, you will frequently get interruptions in the middle of your calls. To find if there is any maintenance work been carried out on the phone transmitters, give the customer service a call to find out.
3) If you are using the iphone4 using your left hand and holding it in that hand, like in the picture provided above, you are covering up the antenna. A antenna is a device in mobile phones that receives signal from the phone mast, if you block it, by holding the device in your left hand on this handset, you are preventing it to gain signal and the signal strength meter will show no bars, which decreases the signal reception gained from the network. This is because the two sides in the black strip on the metal band get covered up, this problem is known as Death Grip. If this is a problem for you, i would suggest you to buy an iphone bumper case, as Apple themselves said its an solution for left hand users because its prevent direct contact with your hands skin onto the strip, which doesn't cause interruption with the antenna.
4) Update the software on your iphone 4, as you might have the old software version that had bugs, which caused signal problems for users that makes calls on the mobile phone. By updating it your signal strength will certainly improved and will become more stronger and you will also benefit from the new feathers included in the update.
Subscribe to:
Posts (Atom)
